Abstract. Objective. This article reflects the importance of low-pressure micro hydropower plants today, information about the problems, causes and ways to solve them. The problems of micro hydroelectric power stations continue to be studied all over the world. Opinions and recommendations are important because the scientific works and literature of about 20 world scientists and researchers were studied as sources, as well as scientific information. Methods. About 20 literatures have been studied, which consider the design of microhydroelectric power plants operating in low-pressure water sources, the factors causing power losses in them. Based on the research results, the energy relationships between their constructive and geometric dimensions are analyzed. Factors affecting efficiency were calculated. Results. Based on the analysis of the literature, calculations were made for the impeller of the turbine of a microhydroelectric power station. The number of nozzles in the turbine, the angle of inclination, the number of guide vanes, the central angle between the guide vanes, the water flow rate, the diameter of the guide device, the feed cylinder, the taper angle at which the water flow rate is the least energy in flat compression. The calculations were revised by introducing boundary conditions for several options. It has been established that when the radius R2 of the guiding cylinder is equal to the radius of the supply cylinder, the energy losses for energy expansion (compression) are minimal. It was found that the diameter of the impeller of a hydraulic turbine can be changed to fit the size of the nozzle, however, an increase in the diameter leads to an increase in the moment of inertia about its center and a sharp decrease in the rotational speed . The water intakes of the hydraulic turbine feed cylinder and the nozzle are made round, and the ratio between their surfaces is analyzed. Conclusions. The diameter of the water supply cylinder of the hydroturbine has been increased in places where it is planned to work in sources with high water consumption and low pressure. This situation leads to an increase in the diameter of the impeller. Exceeding the critical value of the impeller diameter leads to an increase in the moment of inertia and a decrease in the speed of the impeller. This, in turn, leads to excessive energy losses due to the use of additional pulleys or gearboxes.
| Mualliflar | Begmatov, Eldorjon |
|---|---|
| Jurnal | Наманган муҳандисликтехнология институти илмийтехника журнали |
| Nashr sanasi | 2023-06-30 |
| Jild | 8 |
| Son | 2 |
| Betlar | 196-205 |
| Til | Ingliz |
Objective. Due to the technical failure of the line, illegal connections, temperature rise in the cable occurring in the section between the electricity distribution point and the consumer meter of the overhead power…
Objective. This article is devoted to the state program «Strategy of actions in five priority areas of development of the Republic of Uzbekistan in 2017-2021» and «The New Uzbekistan’s Development Strategy» developed…
The article is devoted to the description of the drying method of liquid liquid vehiclesproduced on the basis of a joint solution of heat generated by the authors. The number of leather layers,thermophiles properties…
Objective. The purpose of this study is to study the adhesive properties of samples of an aqueous emulsion of an epoxy thermosetting polymer, as well as to conduct comparative analyzes of the results of tests performed…
Cotton gins are used for ginning in regional cotton gins and clean districts ofUzbekistan using ginning devices of UK or 1XK type and pile-drums of their original design. Damage tothe natural properties of cotton in the…
In the article, a new chain drive structure with elastic elements is designed for the seed distribution device drive. At the same time, the parameters of the proposed chain drive are defined.
In this article, vegetables such as cucumbers, carrots, and cabbage are given in differentamounts The effect of enzymes such as Pectomaserin, Pectinex Ultra SP-L, Pectomaserin G10X,Fructozyme M and increased juice…
Background of the problem. At present, many scientific results are being achieved in our country on the use of local mineral fillers in the field of composite materials production. To date, the use of mineral products…
Objective. For the development of mobile structures of solar drying devices, it is proposed to use a composite film developed on the basis of functional ceramics as a transparent wall. Determination of comparative…
Abstract. Objective. The purpose of the study is to analyze the organizational and economic mechanisms related to the state support of industrial exports in the developed countries of the world and to identify the main…
Наманган муҳандисликтехнология институти илмийтехника журнали — barcha maqolalar