Improvement and Research of a Machine for the Pre-Finishing of Leather and Fur

Tursunboyev, Lochinbek, Турсунбоев, Лочинбек, Tursunboyev, Lochinbek

Mexanika muammolari jurnali · 2026-yil

Annotatsiya

The article presents a systematic review of technological machines and devices, as well as technologies for grinding and finishing leather and the dermal tissue of fur. A grinding machine has been developed that enables the processing of leather and fur semi-finished products while ensuring the full utilization of abrasive materials. Owing to the possibility of reversing and rapidly replacing the abrasive sheets on the working drum, conditions are created for carrying out the grinding process under an optimal operating mode depending on the type and properties of the leather raw material. In addition, a rational substantiation of the geometric, kinematic, and control parameters of the machine equipped with a grinding drum contributes to improving its economic efficiency and ensuring reliable operation. This study analyzes the strength of the working drum of a drum-type leather grinding machine. The drum is considered as a cylindrical shaft rotating under load. During leather grinding, friction forces and, in some cases, non-uniformly distributed loads act on the drum surface. Since the drum operates continuously in a rotating mode, its wall is subjected to centrifugal force caused by rotation, contact pressure with the leather, bending induced by loads transmitted to the drum axis, and torsional stress caused by the torque transmitted through the shaft. Therefore, the drum must be analyzed as a complex mechanical system. The computational and theoretical study of the manufactured grinding drum showed that, at a rotational speed of \(n=1200\) rpm and an average design radius of \(r=0.145\) m, the circumferential normal stress is approximately \(2.61\) MPa. Verification of the computational model in the limiting case showed that, in the absence of rotation, \(\omega \to 0\), the circumferential stress tends to zero. It was also established that the stress depends linearly on the material density and quadratically on the angular velocity and radius. The obtained computational results confirm the consistency of the adopted analytical model with the parameters of the manufactured grinding drum.

Maqola ma’lumotlari
MualliflarTursunboyev, Lochinbek, Турсунбоев, Лочинбек, Tursunboyev, Lochinbek
JurnalMexanika muammolari jurnali
NashriyotМеханика ва иншоотлар сейсмик мустаҳкамлиги институти
ISSN2010-7250
Nashr sanasi2026-10-14
Jild37
Son3
Betlar123-135
TilIngliz
Ilmiy sohaTexnika
Indeksga qo‘shilgan2026-10-18

Maqolaning asl sahifasi

Kalit so‘zlar

leather grinding, pelt dermis, abrasive processing, grinding machines, contact pressure, automation, finishing, processing pressure, abrasion resistance, шлифование кожи, кожевая ткань меха, абразивная обработка, шлифовальные машины, контактное давление, автоматизация, финишная обработка, давление обработки, абразионная стойкость, terini silliqlash, mo‘ynaning teri to‘qimasi, abraziv ishlov berish, silliqlash mashinalari, kontakt bosimi, avtomatlashtirish, yakuniy pardozlash, ishlov berish bosimi, abraziv yeyilishga chidamlilik

Ilmiy soha

Texnika

Iqtibos keltirish

APATursunboyev, Lochinbek, Турсунбоев, Лочинбек, & Tursunboyev, Lochinbek (2026). Improvement and Research of a Machine for the Pre-Finishing of Leather and Fur. Mexanika muammolari jurnali, 37(3), 123-135. https://www.pmjournal.uz/index/article/view/32
GOST (OAK)Tursunboyev, Lochinbek, Турсунбоев, Лочинбек, Tursunboyev, Lochinbek Improvement and Research of a Machine for the Pre-Finishing of Leather and Fur // Mexanika muammolari jurnali. – 2026. – T. 37, № 3. – P. 123-135.
MLATursunboyev, Lochinbek, Турсунбоев, Лочинбек, and Tursunboyev, Lochinbek. “Improvement and Research of a Machine for the Pre-Finishing of Leather and Fur.” Mexanika muammolari jurnali, 37(3), 123-135, 2026. https://www.pmjournal.uz/index/article/view/32
ChicagoTursunboyev, Lochinbek, Турсунбоев, Лочинбек, and Tursunboyev, Lochinbek. “Improvement and Research of a Machine for the Pre-Finishing of Leather and Fur.” Mexanika muammolari jurnali, 37(3), 123-135 (2026). https://www.pmjournal.uz/index/article/view/32
HarvardTursunboyev, Lochinbek, Турсунбоев, Лочинбек, and Tursunboyev, Lochinbek (2026) ‘Improvement and Research of a Machine for the Pre-Finishing of Leather and Fur’, Mexanika muammolari jurnali, 37(3), 123-135. https://www.pmjournal.uz/index/article/view/32
BibTeX
@article{tursunboyevlochinbek2026,
  title = {Improvement and Research of a Machine for the Pre-Finishing of Leather and Fur},
  author = {Tursunboyev, Lochinbek and Турсунбоев, Лочинбек and Tursunboyev, Lochinbek},
  journal = {Mexanika muammolari jurnali},
  year = {2026},
  volume = {37},
  number = {3},
  pages = {123-135},
  url = {https://www.pmjournal.uz/index/article/view/32}
}

Boshqa maqola uchun iqtibos tayyorlash

Mexanika muammolari jurnali jurnalidan boshqa maqolalar

Mexanika muammolari jurnali — barcha maqolalar · 2026-yil arxivi

Texnika sohasidagi boshqa maqolalar

Texnika sohasidagi OAK jurnallari